Thermal Inlet Gasket - Z22SE

Thermal Inlet Gasket - Z22SE
Thermal Inlet Gasket - Z22SE

Thermal Inlet Gasket (TIG) for Z22SE Supercharged engines- designed to reduce heat-soak from the cylinder head to the inlet manifold. Ideal for use with any supercharged Z22SE engine, but especially big power builds.

Heat management is an area that is often ignored during engine modification. The Thermal Inlet Gasket will help prevent heat from conducting from the cylinder head casting into the inlet manifold, significantly reducing heat soak.

In theory, because of the coolerand denser inlet charge, a small and immediate power increase should be evident (if you can run a little more ignition timing before pre-ignition occurs then power should rise), but their main strength will be in helping to keep temperatures under control during and after prolonged engine use.

This 4mm thick high performance composite gasket, designed for optimal heat insulation,is available forZ22SE Supercharged engines only and is paper coated on both sides to aid sealing.

Note: The TIG is paper coated on each side and designed to seal between two flat surfaces. If there is any doubt about the quality of either surface a thin bead of sealant should be used on both sides (not recommended unless absolutely necessary). If the paper gaskets are damaged during strip down/rebuild, they can be replacedwith a pair of OE gaskets.



Not suitable for N/A (Normally Aspirated) Non Supercharged 2.2 engines

Enquiry Form.

Write a review

Please login or register to review
  • Views: 4896
  • Product Code: TIGZ22SE
  • Availability: 10
  • £45.00
  • Ex Tax: £37.50
Idle Pulley, Alloy Bracket,Bolt and washers for use in Z22SE 2.2 16v supercharger conversion. R..
£95.40
Ex Tax: £79.50
Alternator Bolts required for Z22SE supercharger conversion. Includes form C washers.Supplied in Pai..
£1.50
Ex Tax: £1.25
Bolts and Washers for securing the supercharger assembly to the supercharger inlet manifold.Supplied..
£1.20
Ex Tax: £1.00
High Tensile 12.9 Bolts with Washers for mounting the Supercharger Inlet Manifold to the Z22SE 2.2 H..
£2.90
Ex Tax: £2.42
Bolts and Washers for mounting the 2.2 throttle body to the supercharger assembly.Supplied as a Set ..
£0.70
Ex Tax: £0.58
Rubber Hose. Oil/Pressure Resistant. Flexible mineral oil hose for engineering oils, fuel oil, diese..
£6.00
Ex Tax: £5.00
Please Note: Plugs are listed individually.The Best Plugs to use for 1.6 Turbo (Z16LEx/A16LEx/B16LER..
£9.00
Ex Tax: £7.50
Genuine OE Vauxhall/Opel Valve Stem Oil Seal.Vauxhall/Opel Part Number: 90410741For the Z20LEx famil..
£1.50
Ex Tax: £1.25
Shim for M32 Late Type End Case.To ensure correct shimming of the gearbox when fitting the later end..
£2.40
Ex Tax: £2.00
Uprated Exhaust Mount manufactured from a high temperature polyurethane material in red with a Shore..
£10.80
Ex Tax: £9.00
Laser Iridium NGK manufactured Spark Plugs for 2.0 Turbo A20NFT[LHU] A..
£14.40
Ex Tax: £12.00
Clutch Cover to Flywheel Bolt (M7x22) for C20LET and C20XEPreviously: 900652946 Required per Clutch..
£0.60
Ex Tax: £0.50
Gates Cambelt Kit for Z20LET engines. This kit contains a cambelt, pullies, & water pump wi..
£147.00
Ex Tax: £122.50
Genuine GM Big End Bearing Kit, Contains standard size bearing for 4 cond rods. Fits:  &nb..
£38.40
Ex Tax: £32.00
Genuine GM Main Bearing Kit that includes 5 Standard size bearings one of which is the guide/ thrust..
£43.80
Ex Tax: £36.50
10x Genuine GM Cylinder Head Bolts.Fits Models Astra J GTC VXR A2.0NFT (LHU) Astra J GTC V..
£20.88
Ex Tax: £17.40
Oil Pump Assembly Astra J VXR A20NFT B20NFT & Insignia A20NHT New Sorry Out Of Stock
Genuine GM A20NFT Astra J VXR oil Pump Fits Astra J 2.0 GTC VXR A20NFT  (LHU)   ..
£219.00
Ex Tax: £182.50
Rear main oil seals and retaining flange to suit Astra H and Zafira B Z19DTL Z19DTJ & Z19DTH eng..
£30.00
Ex Tax: £25.00